Singer Sewing Machine Tradition 2277 Manual

The Singer Tradition 2277 is a versatile mechanical sewing machine designed for home use, featuring 23 built-in stitches, a 4-step buttonhole, automatic needle threader, adjustable stitch length and width, free arm capability, built-in storage, and a heavy-duty metal frame. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Heavy-duty metal frame, Stitch selection dial, Stitch length and width controls, Automatic needle threader, Free arm, Built-in accessory storage, Foot pedal, Power cord.

Unpacking and Setup

Unpack and inspect contents. Place on a stable, flat surface.

1. Remove machine and accessories from packaging.
2. Attach power cord to machine and plug into a 120V AC outlet.
3. Attach foot pedal to machine and place on floor.
4. Install needle: Loosen needle clamp screw, insert needle with flat side to the back, tighten screw.
5. Attach presser foot: Raise presser foot lever, snap foot into place.

WARNING! Machine is heavy; lift with care. Ensure all parts are securely attached.

First-Time Use

Power on machine; follow steps to thread and test.

1. Wind bobbin: Place thread on spool pin, guide through bobbin winder tension, press bobbin onto winder shaft, engage bobbin winder, press foot pedal.
2. Insert bobbin: Open bobbin cover, drop bobbin in with thread unwinding counterclockwise, pull thread through slot.
3. Thread upper thread: Raise presser foot, follow numbered threading path on machine, use automatic needle threader.
4. Draw up bobbin thread: Hold upper thread, turn handwheel toward you to lower and raise needle, pull thread to bring up bobbin loop.
5. Test sew on scrap fabric.

CAUTION! Keep fingers away from needle during operation.

Specifications

• Type: Mechanical Sewing Machine.
• Built-in Stitches: 23.
• Buttonhole: 4-step manual.
• Stitch Length: Adjustable 0-4 mm.
• Stitch Width: Adjustable 0-5 mm.
• Needle Threader: Automatic.
• Free Arm: Yes, removable flatbed.
• Frame: Heavy-duty metal.
• Power Source: 120V AC, 60Hz.
• Included Accessories: All-purpose foot, buttonhole foot, zipper foot, button sewing foot, seam ripper, needles, bobbins, spool caps, lint brush, screwdriver.

Controls and Functions

Access controls via dials and levers on front and side.

Front Panel: Stitch selection dial, Stitch length control, Stitch width control, Reverse stitch lever, Presser foot lever, Handwheel.

Stitch Selection: Turn dial to select stitch (straight, zigzag, decorative, stretch). Stitch Length: Adjust for shorter/longer stitches. Stitch Width: Adjust for wider/narrower zigzag. Reverse: Hold lever to sew in reverse. Presser Foot Pressure: Adjustable for different fabrics. Tension Control: Adjust upper thread tension (default 4).

Threading the Machine

Upper threading and bobbin insertion.

1. Raise presser foot and needle to highest position.
2. Place thread spool on spool pin.
3. Follow threading path: Through thread guide, down to tension discs, up to take-up lever, down to needle.
4. Use automatic needle threader: Lower lever, hook thread, release lever to pull thread through needle eye.
5. For bobbin: Wind bobbin fully, insert into bobbin case with thread unwinding counterclockwise, pull thread through slot.

Tip: Ensure presser foot is raised when threading to open tension discs.

Stitch Selection and Settings

Supports various stitches for different fabrics and projects.

1. Select stitch: Turn dial to desired stitch number.
2. Adjust length: For straight stitches, use 2-2.5 for general sewing; for zigzag, use shorter length.
3. Adjust width: For zigzag and decorative stitches, set width as needed.
4. Test on scrap fabric to check tension and appearance.
5. For buttonhole: Select buttonhole stitch, mark buttonhole on fabric, use 4-step process (zigzag right, bar tack, zigzag left, bar tack).
6. For reverse: Hold lever to reinforce beginning and end of seams.

WARNING! Do not change stitch selection while needle is in fabric.

Maintenance and Cleaning

Unplug before cleaning. Remove lint and dust regularly.

1. Remove needle plate screws and lift off needle plate.
2. Use lint brush to clean feed dogs and bobbin area.
3. Oil machine as per manual instructions (use only Singer sewing machine oil).
4. Wipe exterior with soft, dry cloth.

CAUTION! Do not use compressed air; it can force lint deeper. Never oil plastic parts.

Accessories

Included accessories and their uses.

Safety Information

Always unplug machine when not in use, during cleaning, or when changing needles. Keep fingers away from moving parts. Do not operate with damaged cord. Use only Singer recommended accessories. Keep machine away from water and heat sources.

Troubleshooting

Reset: Unplug machine for 5 minutes if electronic issues occur.

Service: For repairs, contact authorized Singer service center. Visit www.singer.com or call 1-800-4-SINGER.