singer model 2932 manual

The Singer Model 2932 is a versatile household sewing machine featuring multiple built-in stitches, automatic needle threading, adjustable stitch length and width, a drop-in bobbin system, and a free arm for cylindrical sewing. It operates on standard household power (120V AC, 60Hz) and includes essential accessories such as presser feet, bobbins, needles, and a seam ripper. Below are key sections covering safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Sewing head with stitch selection dial, Bobbin case and drop-in bobbin system, Foot pedal, Power cord and connector, Accessory storage compartment.

Installation & Setup

Unpack and inspect all contents. Place machine on a stable, flat surface.

1. Connect power: Plug power cord into machine and then into a 120V AC outlet.
2. Install foot pedal: Connect pedal to machine port; place on floor.
3. Attach accessories: Snap on desired presser foot; insert needle securely.
4. Wind and insert bobbin: Follow threading diagram to wind bobbin, then place in bobbin case.

WARNING! Keep fingers away from needle area during setup and operation. Ensure machine is unplugged during accessory changes.

First-Time Operation

Power on machine; familiarize yourself with controls.

1. Thread the machine: Follow numbered threading path on machine; use automatic needle threader if available.
2. Insert bobbin: Place wound bobbin in drop-in case with thread pulling counterclockwise.
3. Select stitch: Turn dial to desired stitch pattern (e.g., straight stitch).
4. Test sew: Place fabric under presser foot, lower foot, and gently press foot pedal to sew.

CAUTION! Always turn handwheel toward you (counterclockwise) to avoid timing disruption. Start sewing at slow speed.

Specifications

• Model: Singer 2932.
• Stitches: Multiple built-in stitches (straight, zigzag, stretch, decorative).
• Stitch Length: Adjustable up to 4mm.
• Stitch Width: Adjustable up to 5mm.
• Bobbin: Class 15 transparent bobbin (drop-in system).
• Needle: Standard domestic sewing machine needle (size included).
• Power Source: 120V AC, 60Hz.
• Included Accessories: All-purpose foot, zipper foot, buttonhole foot, bobbins, needles, seam ripper, brush, screwdriver.
• Warranty: Limited warranty as per Singer terms.

Controls and Settings

Primary controls located on front and side of machine. Stitch Selection Dial: Choose stitch pattern. Stitch Length Dial: Adjust from 0-4mm. Stitch Width Dial: Adjust from 0-5mm. Reverse Stitch Lever: Hold to sew backwards. Presser Foot Lever: Raises/lowers presser foot. Handwheel: Manual control of needle position.

Settings: Tension dial (adjust thread tension, default 4), Presser foot pressure dial (adjust for fabric thickness), Built-in light switch.

Connecting Accessories

Presser Feet: Snap onto shank; ensure foot is securely attached. Needles: Insert with flat side toward back; tighten screw. Bobbins: Use only Class 15 bobbins; wind evenly.

1. Turn power off and unplug machine.
2. Align accessory with mounting point (e.g., presser foot ankle).
3. Secure by snapping or screwing into place.
4. Plug in machine and test function at low speed.

Tip: Refer to accessory guide for specific foot applications (zipper, buttonhole, etc.).

Stitch Selection & Sewing

Supports various fabrics and projects.

1. Select stitch: Turn dial to desired pattern (symbols indicated on dial).
2. Adjust settings: Set length and width as needed for fabric.
3. Position fabric: Lower presser foot onto fabric edge.
4. Start sewing: Press foot pedal gently to begin; guide fabric steadily.
5. Reverse: Hold reverse lever to backstitch at beginning and end of seam.
6. Finish: Raise needle to highest position, raise presser foot, remove fabric, and cut threads.
7. Buttonholes: Use four-step buttonhole foot; follow markings for consistent size.
8. Zippers: Install zipper foot; adjust needle position to sew close to zipper teeth.

WARNING! Never pull fabric while needle is in fabric; let feed dogs move material. Keep hands clear of moving needle.

Maintenance Features

Automatic Needle Threader: Lever assists in threading. Bobbin Winding: Built-in bobbin winder on machine. Drop-in Bobbin View Window: Allows monitoring of bobbin thread. Quick-change Presser Feet: Snap-on system for easy swapping.

Care & Cleaning

Unplug machine before cleaning. Remove lint and dust from bobbin area and feed dogs using small brush. Wipe exterior with dry cloth. Oil as per manual instructions (if required).

CAUTION! Do not use compressed air or liquids inside machine. Store in dry area away from dust.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Singer Manufacturing Company. For support, visit www.singer.com or contact 1-800-4-SINGER. This product conforms to applicable safety standards.

Troubleshooting

Reset: Unplug machine for 5 minutes to reset electronic controls if malfunction occurs.

Service: 1-800-4-SINGER; www.singer.com for authorized service centers.