Singer HD 6800C Manual

The Singer HD 6800C is a heavy-duty, computerized sewing machine designed for advanced home sewing and crafting. It features a powerful motor, a wide variety of built-in stitches, automatic needle threader, top drop-in bobbin system, adjustable presser foot pressure, and multiple accessory feet for specialized tasks. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Heavy-duty metal frame, LCD screen, stitch selection dial, automatic needle threader, top-loading bobbin system, accessory compartment, and foot pedal.

Unpacking and Setup

Unpack and inspect all contents. Place on a sturdy, flat table.

1. Remove all packing materials from the machine and accessories.
2. Attach the foot pedal cord to the machine's port.
3. Plug the power cord into the machine and then into a 120V AC outlet.
4. Install the accessory tray and extension table if provided.
5. Raise the presser foot lever and install the all-purpose presser foot.

WARNING! Machine is heavy; lift with care using both hands. Ensure the table is stable to prevent tipping.

First-Time Use

Power on the machine; the LCD screen will illuminate.

1. Wind and insert the bobbin: Follow the diagram for winding, then place bobbin in the case.
2. Thread the upper thread: Follow the numbered path on the machine and use the automatic needle threader.
3. Raise the presser foot and pull up the bobbin thread.
4. Select a basic straight stitch using the stitch selection dial.
5. Place fabric under the presser foot, lower the presser foot lever, and gently press the foot pedal to start sewing.

CAUTION! Keep fingers away from the needle area while sewing. Always turn the handwheel towards you (counter-clockwise).

Specifications

• Type: Computerized, Heavy-Duty Home Sewing Machine.
• Stitches: 100+ built-in stitches.
• Buttonholes: One-step automatic buttonholes.
• Max Sewing Speed: Up to 850 stitches per minute.
• Needle Positions: Adjustable left, center, right.
• Presser Feet: Snap-on system, multiple feet included.
• Bobbin: Class 15 transparent, top-loading.
• Power Source: 120V AC, 60Hz.
• Warranty: 25-year limited warranty.

Controls and Functions

Access settings via the LCD screen and control buttons. Front Panel: Power Switch, Stitch Selection Dial, LCD Screen, Stitch Length/Width Buttons, Reverse Stitch Button, Needle Up/Down Button.

LCD Screen Displays: Selected stitch number, recommended presser foot, stitch length, stitch width, and error messages.

Stitch Adjustment: Use +/- buttons to adjust stitch length (0-4mm) and width (0-7mm). Utility Functions: Reverse stitch, automatic thread cutter (if equipped), speed control slider, start/stop button (for sewing without foot pedal).

Stitch Selection and Settings

Use the stitch selection dial to choose from utility, stretch, decorative, and buttonhole stitches.

1. Turn the dial to the desired stitch number (refer to stitch chart).
2. The LCD will show the default length/width and recommended foot.
3. Adjust length/width using the buttons if needed.
4. For buttonholes: Select the one-step buttonhole, place fabric under foot, and follow the automatic sequence.
5. Always test stitch settings on a fabric scrap first.

Tip: Lower the feed dogs when darning or free-motion quilting. Use the appropriate presser foot for the selected stitch.

Threading and Bobbin Winding

Correct threading is essential for proper stitch formation.

1. Winding the Bobbin: Place spool on pin, guide thread through tension disc, wind onto empty bobbin. Machine will stop automatically when full.
2. Inserting the Bobbin: Place full bobbin in case with thread pulling counter-clockwise. Drop case into compartment; thread should snap into the tension spring.
3. Upper Threading: Follow the numbered path from spool pin to needle. Use the automatic needle threader lever for the final step.
4. Drawing Up Bobbin Thread: Hold the upper thread tail, turn the handwheel toward you until the needle goes down and up, then pull the upper thread to bring the bobbin loop up.

WARNING! Ensure presser foot is raised when threading the upper thread to open the tension discs. Use the same thread type in the bobbin and needle for best results.

Care & Maintenance

Unplug the machine before any cleaning or maintenance.

1. Cleaning: Use the small brush provided to remove lint from the bobbin area, feed dogs, and needle plate. Wipe the exterior with a soft, dry cloth.
2. Oiling: This machine is permanently lubricated at the factory. Do not oil unless specified in the manual for specific points (refer to maintenance section).
3. Needle Replacement: Turn power off. Loosen the needle clamp screw, remove old needle, insert new needle with flat side to the back, and tighten screw firmly.
4. Storage: Cover the machine when not in use to prevent dust accumulation.

CAUTION! Never use compressed air to clean lint, as it can force debris into the motor. Never immerse the machine in water.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Singer Licensing B.V. All rights reserved. For support, visit www.singer.com or contact Singer Customer Service at 1-800-4-SINGER.

Troubleshooting

Reset: Turn the power off, wait 10 seconds, and turn it back on to clear temporary errors.

Service: 1-800-4-SINGER; www.singer.com