Singer 7470 Sewing Machine Manual

The Singer 7470 is a computerized sewing machine featuring 70 built-in stitches, automatic needle threader, automatic thread cutter, adjustable stitch length and width, one-step buttonhole, drop-in bobbin system, LED lighting, speed control slider, and free arm capability. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized control panel, Automatic needle threader, Drop-in bobbin system, Free arm, LED work light, Foot pedal, Accessory storage.

Installation & Setup

Unpack and inspect contents. Place on stable, flat surface.

1. Remove machine from packaging: Lift from case, remove all protective materials.
2. Attach foot pedal: Plug into machine's pedal port.
3. Connect power: Plug power cord into machine, then into 120V AC outlet.
4. Install needle: Loosen needle clamp screw, insert needle flat side back, tighten.
5. Wind bobbin: Place thread on spool pin, guide through bobbin winder, press foot pedal.

WARNING! Keep fingers away from needle area during setup. Ensure machine is unplugged when installing needle.

First-Time Use

Power on machine; LED light turns on.

1. Thread machine: Follow numbered guides, use automatic needle threader.
2. Insert bobbin: Drop bobbin into case, thread through slot, pull under presser foot.
3. Select stitch: Use stitch selection dial or buttons.
4. Test sew: Place fabric under presser foot, lower presser foot lever, gently press foot pedal.
5. Adjust tension: Use tension dial if stitches are uneven.

CAUTION! Always lower presser foot before sewing. Keep hands clear of moving needle.

Specifications

• Model: Singer 7470.
• Stitches: 70 built-in (utility, decorative, stretch).
• Buttonholes: One-step automatic.
• Needle Threading: Automatic.
• Thread Cutter: Automatic.
• Bobbin: Drop-in, Class 15 transparent.
• Lighting: LED.
• Speed: Adjustable up to 750 stitches per minute.
• Power Source: 120V AC, 60Hz.
• Included: All-purpose foot, zipper foot, buttonhole foot, seam ripper, needles, bobbins, spool caps, auxiliary spool pin, duster, foot pedal, power cord.

Controls and Settings

Access settings via control panel buttons and dials.

Control Panel: Stitch selection dial/buttons, Stitch length adjustment (+/-), Stitch width adjustment (+/-), Reverse stitch button, Automatic thread cutter button, Needle up/down button, Speed control slider.

Stitch Selection: Turn dial or press buttons to select stitch number. Stitch Length: Adjust from 0-4 mm. Stitch Width: Adjust from 0-5 mm for zigzag and decorative stitches. Tension: Dial for upper thread tension (3-5 for normal fabrics).

Connecting Accessories

Presser Feet: Snap-on system. Attach by raising presser foot lever, aligning foot with shank, lowering lever to lock.

1. Turn off machine before changing accessories.
2. Select correct foot for stitch type (e.g., buttonhole foot for buttonholes).
3. Ensure foot is securely attached.

Tip: Refer to stitch chart for recommended presser feet.

Stitch Selection & Sewing

Supports straight, zigzag, decorative, and stretch stitches.

1. Select stitch: Use dial or buttons; number displays on panel.
2. Adjust settings: Set length/width as needed.
3. Position fabric: Under presser foot, lower presser foot lever.
4. Start sewing: Press foot pedal lightly; use speed control slider to limit max speed.
5. Reverse: Press reverse button to backstitch at beginning/end of seam.
6. Cut threads: Press automatic thread cutter button after sewing.
7. Buttonhole: Attach buttonhole foot, place button in foot, select buttonhole stitch, press foot pedal.
8. Needle position: Use needle up/down button to stop with needle in fabric or up.

WARNING! Do not pull fabric; let feed dogs move it. Always use correct needle for fabric type.

Maintenance Features

Automatic Needle Threader: Push lever down, hook thread, release lever. Automatic Thread Cutter: Press button after sewing. Bobbin Warning: Indicator light alerts when bobbin is low.

Care & Cleaning

Unplug before cleaning. Remove lint from bobbin area and feed dogs with brush. Wipe exterior with dry cloth.

CAUTION! Do not use compressed air; it can force lint into machine. Oil only as specified in manual.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Singer Manufacturing Company. For support, visit www.singer.com or contact 1-800-4-SINGER.

Troubleshooting

Reset: Turn machine off and on to reset computerized functions.

Service: 1-800-4-SINGER; www.singer.com